How To Stack A 3 Tier Cake With Pillars

How To Stack A 3 Tier Cake With Pillars. How do you stack cake layers without breaking them? Measure height of each stacked cake except the top tier.

Wedding Cake Pillars And Plates & Wilton Wedding Cake Pillars Best from pezcame.com

Poke the cut dowel rods into the base cake, with a gap of 2 to 3 inches apart, but within the diameter of the next tier cake. Smooth about 1 tablespoon of buttercream over the 8″ cake board and place your first layer of your 8″ cake on top. If you try to stack a cake that is still slightly warm in the center, you will meet with disaster.

Source: www.pinterest.com

Separator plates connected by pillars must always be the same size in diameter). Place the third layer, top side up, on top of the cake.

Source: pezcame.com

Take a cake circle and mark where the other cake is going to be placed on the bottom cake then take it off. Smooth the frosting out with a bread dough scraper so that it’s totally smooth.

Source: www.youtube.com

That is what i am looking at to build my 3 tiered cake. Purple ribbons are added to the bottom tiers of the cake and finished with white snail trail/bead borders.

Source: www.wilton.com

Once you have the cake assembled, you cut a dowel the height of the entire cake then sharpen one end and then gently but firmly using a hammer or mallet tap the sharpen end thru all the tiers, cardboard. Position the separator plate (feet up) that will support the tier on pillars.

Source: thecakegirls.com

There mustn't be any residual heat in the cake whatsoever. Place the third layer, top side up, on top of the cake.

Source: www.wilton.com

Stack a cake using pillars and dowel rods. You can also use a layer of fondant over the top and sides of your cake to make sure they’re perfectly smooth.

Source: decoratedtreats.com

Purple ribbons are added to the bottom tiers of the cake and finished with white snail trail/bead borders. Cut the dowel rods even with the height of the cakes.

Source: www.youtube.com

Place a large dollop of frosting on top of the top layer, and smooth it gently over the top and down the sides. The sharpened end should penetrate through each cake board and then embed itself into the base cake board.

Source: www.pinterest.co.uk

Once you have the cake assembled, you cut a dowel the height of the entire cake then sharpen one end and then gently but firmly using a hammer or mallet tap the sharpen end thru all the tiers, cardboard. Each tier would typically require 4 pillars, so if you are making a 3 tiered cake, then you will need 2 sets of such pillars.separator plates, on the other hand, serve the same purpose as cake boards, but these plates come with special knobs underneath (normally 4 knobs to hold 4 pillars)which helps secure the cake pillars, resulting in a very stable cake support structure.

Carefully Position The Plated Tier On The Pillars.

How do you stack cake layers without breaking them? Place a 10″ cake board on the turntable. Build up any low or lopsided spots with frosting.

All The Other Tiers Stand On Their Own Thin Cake Boards Which Should Be The Same.

Purple ribbons are added to the bottom tiers of the cake and finished with white snail trail/bead borders. Once you have done that, you can start stacking up the cakes on one another. Then place the 8″ cake board on top and press down to seal.

Insert Dowel Rods Into Cakes, Spacing About 1 1/2In.

A little additional royal icing will keep the flower secure. Stack a cake using pillars and dowel rods. Use any combination of dowel rods, boards, separator plates and pillars.

A Small Lump Of Sugarpaste Can Also Be Used On The Edge Of The Cake As A Cushion To Stick The Flower Into.

Repeat the process for all cake layers except for the topmost one. Place a large dollop of frosting on top of the top layer, and smooth it gently over the top and down the sides. When stacking buttercream cakes, make sure they are chilled, as it’s so much easier to work with hard but soft icing.

Smooth About 1 Tablespoon Of Buttercream Over The 8″ Cake Board And Place Your First Layer Of Your 8″ Cake On Top.

After the cake is stacked completely you can stabilize it further by running a long wooden dowel with a sharpened end through all the cake tiers from the top; Cut all the dowels of the same height for each tier. If your cake is not levelled the dowel will stick out of the cake that is completely fine as this will result in a complete levelled stacked cake in the end.